#BASIC ROUTER CONFIGURATION SERIAL#
#BASIC ROUTER CONFIGURATION MANUAL#
#BASIC ROUTER CONFIGURATION PASSWORD#
#BASIC ROUTER CONFIGURATION PC#

You successfully configured R2 with initial settings. R1(config)#banner motd #Authorized Access Only!#Д®xit global configuration mode and save the configuration. R1(config-line)#exitД®nter the banner Authorized Access Only! and use # as the delimiting character. R1(config)#line vty 0 4Д®xit line configuration mode and encrypt all plaintext passwords.

#BASIC ROUTER CONFIGURATION PASSWORD#

R1(config)#line console 0Д¬onfigure cisco as the vty password for lines 0 through 4 and require users to login. R1(config)#enable secret classД¬onfigure cisco as the console line password and require users to login. Router#configure terminalД¬onfigure class as the secret password.

In this Syntax Activity, you will configure basic settings for R2.Д®nter global configuration mode and name the router R2. Syntax Checker вЂ“ Configure Basic Router Settings Save the changes on a router, as shown in the example. R1(config)# banner motd $ Authorized Access Only! $ End with CNTL/Z.Д¬onfigure a banner to provide legal notification of unauthorized access, as shown in the example. Router# configure terminalД®nter configuration commands, one per line.

Name the device to distinguish it from other routers and configure passwords, as shown in the example. For example, the following configuration tasks should always be performed. In addition, both devices have similar initial configuration steps. They support a similar modal operating system, similar command structures, and many of the same commands. This topic teaches you basic router configuration and provides two Syntax Checkers and a Packet Tracer activity so you can practice these skills.Д¬isco routers and Cisco switches have many similarities. If you want devices to be able to send and receive data outside of your network, you will have to configure routers. Up to now, this module has only covered switches.

Packet Tracer- Configure Router Interfaces.

Syntax Checker вЂ“ Configure Router Interfaces.

Syntax Checker вЂ“ Configure Basic Router Settings.

#BASIC ROUTER CONFIGURATION PC#

Ping from source pc with the ip 192.168.50.1 to destination host pc ip 192.168.10. network ip-address wildcard-mask area area-idД¬onfiguring Border Gateway Routing protocol (BGP):Д¬onfiguring the Enhanced Interior Gateway Routing Protocol(EIGRP):.Router(config-router)# network network_id.Success rate is 100 percent (5/5), round-trip min/avg/max = 5/7/11 ms Routing Information Protocol (RIP) Configuration: Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:.

#BASIC ROUTER CONFIGURATION MANUAL#

Interface IP-Address OK? Method Status Protocol FastEthernet0/0 192.168.30.1 YES manual up up Serial0/3/0 192.168.20.2 YES manual up up Serial0/3/1 192.168.40.1 YES manual up up Router Foreign Network Configuration Command. Interface IP-Address OK? Method Status Protocol FastEthernet0/0 192.168.30.1 YES manual up upДЇastEthernet0/1 unassigned YES manual administratively down down Serial0/3/0 192.168.20.2 YES manual up up Then check status: for router Router#show ip interface brief If it is DCE ports than assign a clock rate to that ports with 64000 Router#show ip interface brief

#BASIC ROUTER CONFIGURATION SERIAL#

%LINK-5-CHANGED: Interface Serial0/3/0, changed state to downДЇor serial Cables we have to first check its DCE or DTE ports : %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,.%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up.

Router(config)#interface fastEthernet 0/0.

Pick the router Higher than 2800 seriesвЂ¦.

Basic router configuration